RF2IR2W
RF To IR/RS232 Converter-2Way
Quick Start
Installation Instructions
- 1 -
Welcome!
The RF2IR2W base station is the ultimate Xantech accessory to the Xantech XTR39 Color LCD
remote color. It’s a receiver that accepts the Radio Frequency output of the XTR39 remote and
translate it into IR and RS232 command signals that can control virtually any IR or RS232 electronic
device. It can also receive Data Dictionary RS232 commands and transmit them via RF back to the
XTR39 allowing for real-time feedback on the XTR39 display for volume feedback and device status.
Specifications
RF Receive Frequency: 2.4GHz
Channel Address: 16
RS232 Port Interface: Tx, Rx, and Gnd
RS232 Adapter: DB9 Male to Stereo 3.5mm Plug
Network Address: 256 (per Channel Address)
IR Blaster Range: 30’
IR Format Support: XIR1 and XIR2/Library
Addressable Emitter Output Ports: 4
Power Requirements: 12Volts DC @ 300mA
Unit Size: 5.0” x 4.75” x 1.0”
Unit Weight: 4.0 oz
Unit Color: Black with silver logo and model
RoHS Compliant
Default Network Address: 1
Default RS232 Settings: 9600 BAUD, 8-DATA, 1-STOP, NO PARITY
RF2IR2W Diagram (Rear)
- 3 -
RF2IR2W Diagram (Front)
IR and RF LED behavior:
IR LED
On
RF LED
Flash
RF2IR2W Action
Emit IR Commands
Flash
Off
Flash
Flash
Output RS232 Commands
Receive RS232 Commands
Quick Start Instructions
Step 1. Plug the (4) 283M emitters (included) into the RF2IR2W. Next, place the 283M emitter head
directly over the IR eye on the source component to be controlled.
Step 2. Plug the RS232 Adapter Cable into the RF2IR2W port labeled RS232. Next, connect the DB9
plug to the source component to be controlled. In some instances, a null modem converter may be
required. Below is a pin-out of the RS232 Adapter Cable.
- 4 -
Step 3. Plug the power supply into the RF2IR2W port labeled 12VDC. The IR and RF LED lights will
illuminate for 10 seconds. This is part of the start-up sequence. After the LED lights turn ‘off’, the
RF2IR2W is ready to be used.
Step 4. Follow the XTR39 Instructions, RF2IR2W Addendum and follow the steps to setup the
XTR39.
- 5 -
Locating the RF2IR2W
Thanks to Xantech’s superior antenna design, the RF2IR2W can be placed in several locations.
Key Location Points:
• The RF2IR2W should be placed on a flat, stable surface.
• For optimal performance, the RF2IR2W should be placed at a height greater than 3 feet above the
floor. The ideal height should be level to the XTR39 transmitter.
• Avoid placing the RF2IR2W near corners of a room.
• Avoid placing the RF2IR2W next to microwave ovens.
• Using a lower Channel Address will provide the best performance.
Care and Maintenance
Clean the outside of the plastic housing using a soft cloth. Use warm water and mild soap solution.
Do not use abrasive cleaners.
Information
FCC NOTICE
* Section 15.19 Labeling requirements
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and
0197
(2) This device must accept any interference received,
including interference that may cause
undesired operation.
RF2IR2W RF Base Station Quick Start Installation Instructions
© 2008 Xantech Corporation
* Section 15.21 Information to user
The changes or modifications not expressly approved by
the party responsible for compliance
could void the user’s authority to operate the
equipment.
This document is copyright protected. No part of this manual may be
copied or reproduced in any form without prior written consent from
Xantech Corporation.
* IMPORTANT NOTE: To comply with the FCC RF
exposure compliance requirements, no change to the
antenna or the device is permitted. Any change to the
antenna or the device could result in the device
exceeding the RF exposure requirements and void
user’s authority to operate the device.
Xantech Corporation shall not be liable for operational, technical, or
editorial errors/omissions made in this document.
Document Number 08905185A
- 6 -
|