ADTRAN Network Card 234 User Manual

For more detailed documentation, visit us online at www.adtran.com  
TOTAL ACCESS 234 SHDSL NTU  
P/N 1200708L1  
Quick Start Guide  
CONFIGURE GATEWAY IP ADDRESSES/SUBNET MASK  
CONNECT THE CONSOLE INTERFACE  
Before connecting to the Total Access 234 console interface, you will need the following items: VT100  
terminal or PC (with VT100 terminal emulation software) and a straight through serial cable with a DB-9  
(male) connector on one end and the appropriate interface for your terminal (or PC) on the other.  
Configure the Gateway IP addresses and subnet mask by following  
these steps. If you are not sure what IP address to assign, please  
contact your network administrator.  
1. Connect the DB-9 (male) connector of your serial cable to the console port on the rear  
panel of the unit.  
1. Enter enable to activate the Enable command security mode.  
2. When prompted, enter the enable password (if configured).  
3. Enter config terminal to activate the Global configuration mode.  
2. Connect the loose end of the serial cable to the VT100 terminal or PC (with terminal  
emulation software).  
4. Enter bre lan-gw 10.26.12.12 wan-gw 100.26.12.12 mask  
255.255.255.0* to assign LAN and WAN Gateway IP addresses  
and subnet mask.  
3. Open a VT100 terminal session to the Total Access 234 using the following settings:  
9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press <Enter> to activate the  
ADTRAN Command Line Interface (CLI).  
*Note: Underlined text represents example entries only. Modify  
them to match your configuration.  
SPECIFICATIONS  
5. Enter exit to return to the Enable configuration mode.  
DC Input Power  
Diagnostics & Test  
EMC Emissions  
12 VDC nominal (8.5 VDC min, 18 VDC max); ITU-T standards: G.991.2  
Self-diagnosis; local loopback; remote loopback  
6. Enter copy running-config startup-config to save the running  
configuration to the unit’s non-volatile memory (NVRAM).  
EN55022:1998 Class B; FCC Part 15 Class B  
FEATURES  
EMC Immunity, Power  
Fault, and Lightning  
EN55024:1998; EN61000-3-2; EN61000-3-3; Telstra 1563; K.21 (2004)  
Enhanced  
One integrated EIA-232 configuration port (DCE)  
One integrated 10/100BaseT Ethernet port  
2-Wire/4-Wire SHDSL interface  
Electrical Safety  
EN60950; AS/NZS 60950; UL60950 3rd ed.;  
CSA C22.2 No. 60950 3rd ed.; IEC 60950 CB Scheme  
WAN Protocol: ATM  
Telecom  
S043.2; G.991.2  
Command Line Interface (CLI)  
Operating Temp: 0oC to 50oC; Storage Temp: -20oC to 70oC  
Environmental  
Management - EOC/CLI using Virtual Terminal  
Front panel LEDs  
*Note: No stacking should be done at 50oC. Up to three units can be stacked at room temperature.  
Humidity: 95 percent noncondensing  
Wall mounting available with additional parts  
Dimensions  
Connectors  
9.3 inches W x 2.1 inches H x 6.1 inches D  
SHDSL Port: RJ-45; 135 ohms; TNV-3 rated  
10/100BaseT Ethernet: RJ-45  
Table standoff cannot be used with this unit.  
Console Port: DB-9 female  
Power Input: Kycon KPJ-3S snap & lock or equivalent  
Quick Start Guide, 61200708L1-13B, January 2005  
Technical Support 1-888-4ADTRAN or +1-256-963-8716  
Copyright © 2005 ADTRAN, All Rights Reserved  
 

AEG Dishwasher 88070 User Manual
Airfree Air Cleaner Onix 3000 User Manual
Altec Lansing Speaker GT5051 User Manual
Alto Shaam Food Warmer 1000 BQ2 128 User Manual
Amana Clothes Dryer NED7200TW10 User Manual
American DJ DJ Equipment Fire Bowl User Manual
American Dryer Clothes Dryer AD 120ES User Manual
American Standard Plumbing Product M968641 User Manual
AMX Network Card TX MLCD User Manual
Behringer Microphone XM8500 User Manual