ELECTRIC COUNTER TOP
WARMER
OPERATION MANUAL
FW-25
FW-25WT
FW-25 Shown
CECILWARE CORPORATION
43-05 20th AVENUE, LONG ISLAND CITY, NEW YORK 11105-1295 ■
718-932-1414
FAX 718-932-7860
NN56A 5/05
Introduction
Congratulations on the purchase of your Cecilware Counter Top Warmer. Please take a few moments
to carefully read through this manual to ensure the machine is operated and maintained properly. This
will enable the best possible performance from this product for many years.
Cecilware will not accept liability for the following if:
* The instructions in this manual have not been followed correctly.
* Non-authorized personnel have tampered with the machine.
* Non-original spare parts are used.
* The machine has not been handled and cleaned correctly.
Packaging
Cecilware prides itself on quality and service, ensuring that at the time of packing all products are
supplied fully functional and free of damage.
Provided in this package are the following:
* Warmer
* Divider Bar
* Manual
Should you find any damage as a result of freight, please contact your Cecilware dealer immediately.
Installation
Remove the Counter Top Warmer from the packaging. Be certain all protective plastics and residues
are thoroughly cleaned from its surface.
Place the Warmer on a firm level surface clear from all combustible materials.
Supply the appropriate power--(See specifications on page 6). Plug in and turn the power on.
Operation
Fill the Warmer with water to the indicated level. Do not overfill; under no circumstances, should the
food pans float. If this occurs, remove excess water. It is recommended to use fresh clean water for
each use.
To switch on, simply turn the temperature dial clockwise to the desired setting. The red light will glow
to indicate the unit is on. To turn off, simply turn the temperature dial counter clockwise to the 0
setting. It is recommended that the thermostat be set to the maximum heat of 195º F (1 full turn
clockwise) for pre-heating the warmer. An operating setting of 168º F should be sufficient once the
unit is pre-heated.
NOTE: Do not lift, move or carry the warmer when on; nor should you move the unit when it contains
food or water.
2
Cleaning, Care and Maintenance
Switch off the power and disconnect from the source. Ensure that the unit is always switched off and
unplugged while cleaning, maintaining or moving.
The Warmer should be cleaned after each day’s operation; however, additional cleaning may be
required depending on daily use. Before cleaning, allow the warmer to cool down
Empty the water basin, and clean after each use. Pans and lids can be removed to be cleaned. The
Warmer can be wiped down with a damp cloth. Do not immerse the Warmer in water or use hose to
clean.
Warm soapy water is recommended for cleaning. Cleaning agents may cause damage when used for a
prolonged period on stainless steel.
Safety
A Cecilware Recommended Qualified Service Technician should carry out repairs if necessary.
*Switch off power to and disconnect from the outlet when cleaning, maintaining or moving.
To avoid over heating or damage to the element, this unit has been installed with a Hi Limit. If the Hi
Limit is tripped, please call a Recommended Qualified Service Technician to check over the warmer,
repair if needed and reset the Hi Limit.
Trouble Shooting
If your Cecilware Warmer does not operate, please check the following before placing a service call.
Electric Counter
FW-25, FW-25-WT
Top Warmer
Problem
Cause
Remedy
1. Mains power supply
1. Check mains power supply
2. Power switch has not been 2. Check the unit is correctly plugged in and
turned on
turned on
3. Replace the fuse in the plug with correctly
rated fuse
3. Fuse in the plug has blown
The unit is not
working and the
indicator light is not
on
4. On/off switch is faulty
5. Plug and lead are damaged
6. Internal wiring fault
4. Call service agent or qualified technician
5. Call service agent or qualified technician
6. Call service agent or qualified technician
7. This is a safety device that has disconnected
the power: call a service agent or qualified
technician
7. Thermal
activated
cut-out
has
3
Problem
Cause
Remedy
The unit is heating but the 1. The indicator bulb has 1. Replace the indicator light: call a
indicator light is not on
blown
service agent or qualified technician
1.Call service agent or qualified
technician
1.Faulty element(s)
2. Ensure that the thermostat is set
correctly, also ensure the dial is not
spinning on the thermostat and giving the
wrong reading
Indicator light is on but the
unit is not heating
2.Operation of thermostat
3.
Call service agent or qualified
3.Faulty thermostat
1.No water in the pan
2. Thermostat setting
3. Faulty element(s)
technician
1. Fill the pan to the indicated level
(between Min and Max)
2. Ensure that the thermostat is set
correctly, and the dial is not spinning
Slow heat up
3.
Call service agent or qualified
technician
Please ensure:
*There is correct power supply.
*The machine is plugged in correctly and power is switched on.
*The thermostat dial has been turned on.
Note: All Cecilware products are tested prior to packing.
Compliance
Cecilware products have undergone strict product testing in order to comply with regulatory standards
and specifications set by international, independent, and federal authorities.
As testimony to such compliance, Cecilware products carry the following marks/symbols:
4
Electrical Diagram
Model: FW-25, FW-25WT
120V
hi-limit
on/off
switch
thermostat
pilot light
heating
element
The above circuit diagram has been provided to assist qualified technicians. A Recommended Qualified
Service Technician should carry out repairs if needed. Do not remove any components or service panels
on this product.
5
Explosion View
FW-25
1
2
3
14
4
5
6
15
7
13
8
9
12
11
10
FW-25WT
1
2
3
14
4
5
18
17
6
7
15
13
8
9
12
11
10
6
Spare Parts List
No.
1
Description
QTY
1
Part NO
08056
08057
NA
WATER PAN
2
HEATING ELEMENT - 120V, 1500W
ELEMENT FIXING PLATE
INSULATION
1
3
1
4
1
NA
5
INSULATION COVER
PAN HOLDERS
1
NA
6
2
08058
NA
7
MAIN BODY
1
8
BASE PLATE
1
NA
9
FEET
4
08059
08060
08027
08032
08054
08079
08055
08089
08090
08091
10
11
12
13
14
15
16
17
18
THERMOSTAT DIAL
THERMOSTAT
1
1
PILOT LIGHT
1
ON/OFF SWITCH
HI-LIMIT
1
1
CORD & PLUG
1
DRIP TAP
1
FLEXIBLE HOSE CONNECTION
STUFFING PLUG
1
1
*NA = not available except by special order.
Specifications
DIMENSIONS (INCHS)
MODEL
VOLTAGE
POWER
W×D×H
120V
50/60 HZ
FW-25
1500W
14 3/8”×23 1/2”×10 1/2”
14 3/8”×25 3/4”×10 1/2”
120V
50/60 HZ
FW-25WT
1500W
7
CECILWARE CORPORATION
43-05 20th AVENUE, LONG ISLAND CITY, NEW YORK 11105-1295 ■
718-932-1414
FAX 718-932-7860
8
|