ETA-PD8
Power Conditioner & Distribution Unit
ETA-PD8
Power Conditioner & Distribution Unit
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800-321-6699 • Fax: 800-996-3821
– 1 –
ETAsys.com
Specifications are subject to change without notice.
ETA-PD8
Power Conditioner & Distribution Unit
IMPORTANT SAFETY INSTRUCTIONS
The lightning flash with arrowhead symbol within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage “ within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this device near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other device (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the
other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they
exit from the device.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the device. When a cart is used,
use caution when moving the cart/device combination to avoid injury from tip-over.
13 This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a
grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
14. Unplug this device during lightning storms or when unused for long periods of time.
15. Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled, or objects have fallen into the device, the device has been exposed
to rain or moisture, does not operate normally, or has been dropped.
16. WARNING: To reduce the risk of fire or electric shock, this device should not be exposed to rain or moisture and objects filled with
liquids, such as a vase, should not be placed on this device.
17. To completely disconnect this equipment from the mains, disconnect the power supply cord plug from the receptacle.
18. The mains plug of the power supply cord shall remain readily operable.
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800-321-6699 • Fax: 800-996-3821
– 3 –
ETAsys.com
Specifications are subject to change without notice.
ETA-PD8
Power Conditioner & Distribution Unit
WARNING – WHEN THE DEVICE IS IN USE
•
•
To prevent electric shock, do not remove the product cover as there are high voltage components inside. Refer all servicing to
ETA Systems.
Should any of the following irregularities occur during use, immediately switch off the power, disconnect the power cord from the
AC outlet and contact ETA Systems. Do not to attempt to continue operation with the product as this may cause fire or electric shock:
•
•
•
•
•
Smoke or strange smell coming from the unit.
If the product falls or the case is damaged.
If water or any metallic objects falls into the product.
If the power supply cord is damaged in any way.
If the unit is malfunctioning.
•
•
Do not insert or drop metallic objects or flammable materials into the ventilation holes of the product's cover, as this may result in
electric shock or fire.
Do not place any containers with liquid or metallic objects on the top of the product. If any liquid spills into the unit, fire or electric
shock may result.
•
•
•
•
Never operate this product or touch the power supply cord during an electrical storm, electric shock may result.
Never exceed the power rating on the product when connecting equipment. Fire and/or property damage may result.
Operate the product only with the voltage specified on the unit. Fire and/or electric shock may result if a higher voltage is used.
Do not modify, kink, or cut the power cord. Do not place the power cord in close proximity to heaters and do not place heavy objects
on the power cord, including the product itself, doing so may result in fire or electrical shock.
Ensure that the safety ground terminal is connected to a proper ground. Never connect the ground to a gas pipe as a catastrophic
disaster may result.
•
•
Be sure the installation of the product is stable, avoid slanted surfaces as the product may fall and cause injury or property damage.
CAUTION – WHEN INSTALLING THE PRODUCT
•
Installation of this product must be done by a certified electrician for a permanently connected apparatus provided neither with an
all-pole mains switch nor an all-pole circuit breaker. A readily accessible disconnect device shall be incorporated in the building
installation power wiring. The installation shall be carried out in accordance with all applicable installation rules in accordance with all
applicable federal, state, and local laws, regulations, and safety codes and ordinances.
•
•
Never install this product in humid or dusty locations, nor in direct sunlight, near sources of heat, or in areas where sooty smoke or
steam are present. Fire and electric shock may result.
Keep all sides of the unit at least 31⁄2" away from objects that may obstruct air flow to prevent the unit's internal temperature rise.
CAUTION – WHEN THE DEVICE IS IN USE
•
•
•
•
Never place heavy objects on the product, causing it to fall and/or break, resulting in personal injury and property damage. In
addition, the product itself may fall and cause injury and property damage.
Contact ETA Systems for instructions on cleaning the inside of the unit. Large accumulations of dust inside the unit may result in heat
buildup and fire.
Ensure that the power supply plug is securely plugged into the wall outlet. Never allow dust to accumulate on the power plug or
inside the wall outlet.
When cleaning the unit or the unit is not to be operated for an extended period, unplug the power cord from the wall.
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800-321-6699 • Fax: 800-996-3821
– 4 –
ETAsys.com
Specifications are subject to change without notice.
ETA-PD8
Power Conditioner & Distribution Unit
INTRODUCTION
Thank you for purchasing the ETA Systems ETA-PD8 AC Power Conditioner & Distribution Unit. The ETA-PD8 has been designed to
meet most installation requirements for AC power distribution and equipment power protection.
The ETA-PD8 features noise filtering for unwanted Radio Frequency Interference (RFI) that is commonly introduced into AC lines by
nearby radio transmitters or wireless products. EMI filters are incorporated to reduce noise from Electromagnetic Interference (EMI)
from such items as electric motors and switching power supplies. The benefit of these filters can be seen on video products or audibly
by reducing static pops and external signal interference.
Unstable AC Mains voltage is one of the main reasons for equipment failure. The amount of energy that can be injected into the power
system can be immense with voltages reaching 6kV or amperage peaks of 3000A. These spikes are very fast and usually only last for
a very short period of time. The ETA-PD8’s circuitry is very fast and can suppress unwanted energy within a nanosecond response and
sustain the suppression up to 2 milliseconds, thus ensuring virtually trouble free protection.
The ETA-PD8 offers power management control, noise filtering, and spike/surge protection, making it the most compact, effective
power management protection system on the market today.
KEY FEATURES
• 9 Total Outlets
• 6 Rear Panel Switched Outlets and 2 Rear Panel Unswitched Outlets
• 1 Front Panel Unswitched Convenience Outlet
• RFI Noise Filtering to Reduce Radio Frequency Interference
• EMI to Reduce Electromagnetic Interference
• Circuit Breaker Protection @ 15A
• Spike Suppression up to 6000V
APPLICATIONS
The ETA-PD8 was designed to be flexible with features that allow it to be used in a variety of applications. The ETA-PD8 can be
used solely for protection against voltage surges or for AC distribution. If fuzzy video or frequent static pops occur, the AC power
conditioning may eliminate or reduce those inconveniences. The following are just a few examples of applications where the ETA-PD8
can be used:
• Restaurants
• Houses of Worship
• Schools
• Home Theaters
• Office Buildings
• Sports Bars
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800-321-6699 • Fax: 800-996-3821
– 5 –
ETAsys.com
Specifications are subject to change without notice.
ETA-PD8
Power Conditioner & Distribution Unit
FRONT PANEL FEATURES
1
2
3
1. Unswitched AC Outlet – The 120VAC outlet is always live when the ETA-PD8 power cord is plugged into an AC mains power
source and voltage is present. Note: The AC mains power switch does not affect the Unswitched AC Outlet. The Unswitched
Outlet is protected by the surge protection circuitry.
2. AC Mains Breaker – The 15A rated breaker will open if the combined draw of all AC outlets exceeds 15A. Note: The breaker is
designed to exceed its rating for a short period of time. If the breaker is tripped, you must first remove the load from the ETA-PD8
and then push to reset.
3. Power Switch – To turn the ETA-PD8 on or off, press the switch to the ON or OFF position. The power switch will illuminate
when in the “On” position.
REAR PANEL FEATURES
2
3
1
1. AC Mains Input – Connect the 9' (3m) power cord to a 15A 120VAC outlet to provide power to the ETA-PD8.
2. AC Switched Power Outlets – These six outlets are “Live” when the front panel power switch is activated.
3. AC Unswitched Power Outlets – These two outlets are always “Live” when the ETA-PD8 is plugged into a 120VAC source.
Installation
Before installing, we strongly suggest you read the entire manual to ensure you benefit from all the features of the ETA-PD8. The
ETA-PD8 can be placed on a shelf or rack mounted in a standard 19" width rack. When rack mounting, use Rack Rail type screws which
are 10⁄32" x 1" When rack mounted, placement within the rack is flexible however the ETA-PD8 should be within 6' of a dedicated 15A
AC outlet. Always make sure the 15A outlet is properly inspected by a certified electrician prior to connecting the ETA-PD8. Make sure
to inspect the equipment that is to be plugged into the ETA-PD8 to ensure it does not exceed 15A total amperage draw.
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800-321-6699 • Fax: 800-996-3821
– 6 –
ETAsys.com
Specifications are subject to change without notice.
ETA-PD8
Power Conditioner & Distribution Unit
AC POWER CORD RETAINER SYSTEM
Your ETA Systems product comes with an AC Mains Power Cord Retainer System. This system prevents the power
cord from being removed without the use of a screwdriver. Follow these steps for installation.
Note: Installation of this product must be done by a certified electrician for a permanently connected apparatus provided
neither with an all-pole mains switch nor an all-pole circuit breaker. A readily accessible disconnect device shall be
incorporated in the building installation power wiring. The installation shall be carried out in accordance with all applicable
installation rules in accordance with all applicable federal, state, and local laws, regulations, safety codes and ordinances.
1. Locate the 6/32 screw, retainer clip, and zip tie.
4. Wrap the zip tie around the power cord as shown in Figure 4.
2. Locate the AC wall outlet that will be used to power the
Atlas Power product. Remove the center screw securing the
cover plate to the AC outlet.
Figure 4
5. Feed the end of the zip tie through the retainer and pull tightly
to secure. Note: Some adjustment of the retainer may be
needed in order to properly align it as shown in Figure 6.
Figure 1
3. Place the screw through the retainer clip and insert into the
cover plate making sure to securely tighten. Inset the zip tie
through the retainer clip slots as shown in Figure 3.
Figure 5
Figure 6
6. Cut the excess zip tie off as shown in Figure 7.
Figure 2
Figure 3
Figure 7
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800-321-6699 • Fax: 800-996-3821
– 7 –
ETAsys.com
Specifications are subject to change without notice.
ETA-PD8
Power Conditioner & Distribution Unit
ETA-PD8 SPECIFICATIONS
Type
Power Conditioner & Suppressor
15A
Load Rating
Safety Listing
ETL (UL 60065 Standard)
Front Panel
AC Outlets
1 Unswitched
Rocker
Activation Switch
Circuit Breaker
Indicators
15A Resettable
AC Power On
Rear Panel
AC Outlets
8 Total, 6 Switched, 2 Unswitched
9' (3 Meters) 14-gauge
AC Mains Power Cord
Technical Data
Current Rating
15 amps
Power Consumption
6 watts
Operating Voltage
102 - 132VAC
Min. Spike Clamping Voltage
Max. Spike Clamping Voltage
Max. Spike Clamping Resp. Time
Spike Clamping Voltage @ 100A
Maximum Surge Current
Energy Rating @ 2ms
Noise Attenuation EMI/RFI
Temperature Range
460 VRMS @ 3,000A
6kV
1 nanosecond
1250Vp for 20μs
6,500A
200 Joules
10dB @ 10 kHz, 40dB @ 100 kHz, 100dB @ 10 MHz
5º to 35º C
Humidity Range
5% to 95% R.H.
Mechanical
Chassis Finish
Mounting
Black
Rack Mount, 19", 1 RU
Dimensions
Weight
Height 1.75" (44.45mm) x Width 19" (482.6mm) x Depth 5" (127mm)
5 lbs (2.27kg)
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800-321-6699 • Fax: 800-996-3821
– 8 –
ETAsys.com
Specifications are subject to change without notice.
ETA-PD8
Power Conditioner & Distribution Unit
NOTES:
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800-321-6699 • Fax: 800-996-3821
– 9 –
ETAsys.com
Specifications are subject to change without notice.
ETA-PD8
Power Conditioner & Distribution Unit
NOTES:
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800-321-6699 • Fax: 800-996-3821
– 10 –
ETAsys.com
Specifications are subject to change without notice.
ETA-PD8
Power Conditioner & Distribution Unit
NOTES:
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800-321-6699 • Fax: 800-996-3821
– 11 –
ETAsys.com
Specifications are subject to change without notice.
ETA-PD8
Power Conditioner & Distribution Unit
LIMITED WARRANTY
All products manufactured by ETA Systems are warranted to the original dealer/installer, industrial or commercial purchaser to be
free from defects in material and workmanship and to be in compliance with our published specifications, if any. This warranty
shall extend from the date of purchase for a period of one year. Additionally, fuses and lamps carry no warranty. ETA Systems will
solely at its discretion, replace at no charge or repair free of charge defective parts or products when the product has been applied
and used in accordance with our published operation and installation instructions. We will not be responsible for defects caused by
improper storage, misuse (including failure to provide reasonable and necessary maintenance), accident, abnormal atmospheres, water
immersion, lightning discharge, or malfunctions when products have been modified or operated in excess of rated power, altered,
serviced or installed in other than a workmanlike manner. The original sales invoice should be retained as evidence of purchase under
the terms of this warranty. All warranty returns must comply with our returns policy set forth below. When products returned to ETA
Systems do not qualify for repair or replacement under our warranty, repairs may be performed at prevailing costs for material and labor
unless there is included with the returned product(s) a written request for an estimate of repair costs before any non-warranty work is
performed. In the event of replacement or upon completion of repairs, return shipment will be made with the transportation charges
collect.
EXCEPT TO THE EXTENT THAT APPLICABLE LAW PREVENTS THE LIMITATION OF CONSEQUENTIAL DAMAGES FOR PERSONAL
INJURY, ETA SYSTEMS SHALL NOT BE LIABLE IN TORT OR CONTRACT FOR ANY DIRECT, CONSEQUENTIAL OR INCIDENTAL
LOSS OR DAMAGE ARISING OUT OF THE INSTALLATION, USE OR INABILITY TO USE THE PRODUCTS. THE ABOVE WARRANTY IS
IN LIEU OF ALL OTHER WARRANTIES INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE.
ETA Systems does not assume, nor does it authorize any other person to assume or extend on its behalf, any other warranty,
obligation, or liability. This warranty gives you specific legal rights and you may have other rights which vary from state to state.
SERVICE
Should your ETA-PD8 require service, please contact the
ETA Systems warranty department at
1-877-689-8055, ext. 277 to obtain an RA number.
ETA Systems Tech Support can be reached at 1-800-321-6699.
©2014 ETA Systems. All rights reserved. All other trademarks are the property of their respective owners. ETA003561 RevD 3/14
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800-321-6699 • Fax: 800-996-3821
– 12 –
ETAsys.com
Specifications are subject to change without notice.
|