GE Model 19234
The chime and pushbutton must be set to the same
house security code for the combination to operate
together.
Push Button Mounting Instructions
9. Test operation. If the chime does not work, see
TROUBLESHOOTING.
If you do not want to drill holes in your door frame, you
can use the supplied double sided tape for installation.
1. Clean all mounting surfaces with a 50/50 mixture of
isopropyl alcohol.
2. Remove the backing from one side of the double
sided tape and press the exposed side against the
back plate of the push button.
3. Remove the other backing strip and press the
exposed side against the door frame where you want
the button installed.
Note: Avoid mounting on metal surfaces, as it may
result in a reduced range of transmission. Do not mount
in an area where exposed to direct rain.
1. Remove power from the chime.
2. To remove the batteries from the pushbutton,
open the pushbutton case as shown below.
Wireless Door Chime Kit
a. Removing the back cover
Installation Instructions AC Wireless Chime Kit
Required Tools: Small flat blade screwdriver, drill,
1/16” drill bit, and phillips screwdriver.
Included Hardware:
(2) 3x20mm screws
(1) Double sided adhesive pad
Power Indicator
b. Replacing the back cover
The wireless door chime kit has two components:
Pushbutton
House Code
Jumpers
On/Off Switch
Operation
Mounting Push Button
1. Push buttons are typically mounted at the same
height as the door knob or handle (between 36” and
44” above the floor).
2. Before mounting, choose a mounting location that
is not farther than 150 feet from the chime unit
location.
1. Plug the chime into a 120V AC outlet and slide the
power switch to the “On” position to turn on the
chime. The red LED power indicator will light.
2. Gently press transmitter button to sound chime.
Battery Operated
PushButton (Transmitter)
Battery included
Pushbutton Jumpers
Chime (Receiver)
Plugs into 120V outlet
3. Locate the House Security Code door and screw
located on the back of the Chime. Remove the
screw and take off the door.
4. Locate the chime and pushbutton jumpers shown
above.
5. To change the house code, add or remove jumpers
as needed. It is recommended to change only one
jumper at a time and then test the system for proper
operation. The jumpers on the chime and pushbutton
must match exactly.
Troubleshooting
Setting The House Security Code
Not further than 150 feet
Chime doesn’t work:
1. Make sure push button switch is depressed and held
for at least 1 second.
2. Make sure house code switches 1-4 on chime and
push button match exactly.
3. Verify battery orientation in push button.
4. Try fresh batteries.
5. Make sure chime is not farther than 150 feet away
from push button.
Each chime component has 3 jumpers for setting the
house security code. In most cases you will not need
to change the factory settings for the house security
code. If your chime activates intermittently or does not
work at all, you may be able to solve the problem by
changing your security code.
Wireless push button battery
6. Ensure push button is not mounted on metal, near
metal studs, or near the floor.
7. Try a new location for the chime.
To install or replace the battery in the wireless push
button.
3. Before placing the pushbutton where you would like
to mount it, place the chime as close to final position
as possible. Test the operation before drilling. If it
works, mount the push button. If it does not work,
see TROUBLESHOOTING.
Functional range may be adversely affected by one or
more of the following factors: weather, radio frequency
interference, low transmitter battery and obstructions
between the transmitter and receiver.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference, and
2. This device must accept interference received,
including any interference that may cause undesired
operation.
1. Remove the back cover of the push button.
4. Use back cover of push button as a template to mark
two screw holes.
2. Install the A23 (12 volt) battery with the negative
side of the battery (-) toward the spring and the
positive side of the battery (+) toward the positive
battery holder as shown below.
For technical support contact Jasco Products
Company at 1-800-654-8483
4
Made in China/Hecho en China
5
Pushbutton
House Code
Jumpers
is a trademark of
6
General Electric Company
and is used under license to
Jasco Products Company LLC,
10 E. Memorial Rd.,
8
5. Drill two holes with 1/16” size drill in marked
locations.
Oklahoma City, OK 73114.
3. Replace back cover as shown below.
6. Secure back cover to the mounting surface with two
supplied mounting screws.
7. Install the supplied 12V battery observing proper
polarity. (see battery installation section)
8. Press front housing onto back cover.
Rev. 04-10
19234
19234-1.indd
1
4/14/10 3:58 PM
|