Excellent Sound Quality CD/Memory Stick Receiver with MP3/WMA
MODEL
Superb Sound Quality CD Receiver with MP3
MODEL
INSTALLATION MANUAL
Be sure to read this installation manual thoroughly before carrying out installation and making
connections. If installation methods or non-standard parts that are not specified in this installation
manual are used, accidents or injury may result.
Professional installation is recommended, contact the place of purchase to schedule an appointment.
After reading the owner's manual and the installation manual thoroughly, keep them in a safe place for
later reference.
To dealers:
Give this installation manual to the customer after installation and connections have been completed.
Contents
Components
2
3
Before
installation
For your safety in using the CD8445E or CD5425E
Names and functions of terminals
System connection example
4
6
Connections
Installation
Installing the main unit
7
CD8445E or CD5425E
For your safety in using the
Warning and caution signs, illustrated below, are posted throughout this manual as well as on the CD8445E
and CD5425E. They show safe and correct ways to handle the product so as to prevent personal injury to
you and others and to avoid damage to property.
Before reading through the manual, take time to read through and learn the important information listed in
this section.
This sign indicates a situation in which incorrect handling through disregard
of a sign might result in death or serious personal injury.
This sign indicates a situation in which incorrect handling through disregard of a sign
might result in personal injury or may result solely in damage to property.
This section contains information that can help to prevent problems and
damage to the unit, and also contains other useful information.
Tip
• This equipment requires 12V DC and should only be
installed in a vehicle with a 12V negative earth electrical
system. Any other installation may cause a fire or other
severe damage to the equipment and the vehicle.
• Air bags are vital safety equipment. Never install equipment
in a way which will alter air bag wiring or interfere with air
bag deployment. Air bags must function properly in the
event of an accident.
• When installing equipment, do not remove or alter existing
vehicle fasteners, including nuts, bolts, screws, clips, and
fittings. Never detach, move or alter existing vehicle wiring,
including electrical grounds and straps. Alteration of existing
vehicle components may make the vehicle unsafe to
operate.
• For your protection, never use a power drill without safety
glasses or goggles. Debris or broken drill bits may cause
severe eye injuries, including blindness.
• Use electrical tape to insulate the ends of all wires, even if
not used. Proper insulation prevents arcs, shocks and fires.
• Do not disassemble or alter this equipment. Accidents, fires
• Before installation, remove the negative
battery terminal
to prevent shocks, electrical arcing, fires, and damage to
vehicle wiring and the equipment you are installing.
or shocks may result.
• Always replace fuses with fuses of identical capacity and
characteristics. Never use a higher-rated fuse than the
original. Using the wrong type of fuse may cause a fire or
severe damage.
• Secure wiring with tape or plastic ties so that wires do not
interfere with vehicle operation, including brake pedal, gear
shifter and steering. Position wires so that they will not be
rubbed, abraded, or damaged by moving vehicle
components, including power seats.
•Do not modify this system for use other than that specified
herein. Also, do not deviate from the installation procedures
described herein; Eclipse will not be held liable for damages
including, but not limited to serious injury, death or property
damage resulting from installations that enable unintended
operation.
• To avoid equipment and vehicle damage, including fire,
never supply power to installed equipment in a way which
will overload the capacity of an existing vehicle circuit.
Never leave a power supply wire or connection uninsulated.
Always install supplied fuses, circuit breakers, and relays
•
•
Wiring and installing this equipment requires expertise and
Do not block the fan, heat sink or vents for this unit. When
fan, heat sink or vent are blocked, the interior overheats,
and fires may result.
experience. Professional installation is recommended.
Consult with your dealer or a professional installer. Incorrect
wiring may damage the equipment or interfere with safe
vehicle operation.
•
Connect as specified in the installation manual. If not
connected normally, fires or accidents may result.
•
Use only the accessory parts as specified. Using other parts
may cause damage to the equipment or cause parts to fall
or fly off the equipment.
•
When installing in vehicles equipped with air bags, check
the manufacturer's cautions regarding operation before
operating. Airbags may not operate properly.
•
Do not install the unit in places where it may get dew
•
Carry out the wiring such that cords are not pinched by
condensation on (around the air conditioning hose, etc.),
come in contact with water, or in conditions of high
moisture, dust or oily smoke. If water, moisture, dust or oily
smoke enters this unit, smoke, fires or malfunctions may
result.
movable parts such as seat rails, and screw parts of the
vehicle body. Accidents, fires and shocks may result from
disconnection and electrical shorts.
•
Carry out the wiring such that the cord does not make
contact with metal parts. The cord may be damaged by
contact with metal parts, resulting in fire and shocks.
•
Avoid installing in places where it cannot be fastened
securely or where there are strong vibrations. Also, if you
installed the unit with double-sided tape, first wipe away dirt
and wax from the installation area. Otherwise, the unit may
come loose due to vibration while driving, causing problems
for driving and resulting in traffic accidents or injuries.
•
Avoid hot surfaces when wiring equipment. High
temperatures may damage wiring, causing shorts, arcing
and fires.
•
When changing the installation location for this equipment,
•
Do not install in places with direct sunlight or where it will be
please consult the dealer where you bought it for safety
reasons. Expertise is necessary for removal and
installation.
hit directly by hot air from the heater. This may increase the
temperature of the interior of this equipment, resulting in
fires and malfunctions.
- -
3
Names and functions of terminals
•
•
Never cut the insulation on the power cable or use it to power any other equipment. If the rated current
capacity of the power cable is exceeded, fire and electric shocks may result.
The cables should be secured with tape or a similar securing method to prevent any obstructions while
driving. If they get wound or entangled around components such as the steering wheel, shifting lever,
or brake pedal, accidents may result.
•
If removing the end of the cord to connect to another cord, be sure to wrap PVC tape or a similar wire
insulating method around the connection to insulate it. If the connection is not insulated, fire or
accidents may result.
MAIN UNIT
1
ANTENNA PLUG
E
D
16P
C
A
B
INTERCONNECTING CABLE
(Power and speaker connector)
2
4
3
1
Tip*1
Tip*1
TO VEHICLE-SIDE
CONNECTOR
2
• The positions of the B+ and ACC pins on the connector may vary
depending on the vehicle. In such cases, replace the end of the
connector. Ask your dealer for details on connector pin positions.
Tip
This illustration shows the CD8445E. The CD5425E differs slightly from this illustration.
Refer to page 5 for details on the wire colours and connection points for interconnecting cables
•
•
•
.
2
Refer to page 5 for details on connection points
to
for the main unit cables and
A
E
terminals.
- -
4
Wire colours and connection points for connection cables
2
1
Antenna power supply (Blue)
Connect to the automatic-antenna control terminal of the vehicle.
2
Control power supply (Blue/White)
Connect the control terminal for the external amplifier, etc.
3
Cellular phone mute Wire (Pink)
Connect to the earth output terminal on a mobile phone.
4
Earth (Black)
Connect where good body earthing is available.
Main unit connections
E-LAN terminal (13P)
Connect to the E-LAN terminal of the CD changer, etc.
A
Front line-out terminal
B
Connect to the RCA connector of an external amplifier.
Rear line-out terminal
Connect to the RCA connector of an external amplifier.
C
Line-out terminal (Non fader)
D
This is used for non fader output. It can be used as a sub-woofer terminal if a separate amplifier with
a low bass filter is connected.
E
AUX in terminals (CD8445E only)
Connect if using together with portable audio equipment that is sold separately.
* If the output from the connected equipment is via a mini plug, it will need to be converted to RCA.
-
If installing to a vehicle with no ACC position
-
Tip
• If installing to a vehicle with no ACC position, be sure to explain the following to the customer when
handing back the vehicle.
“When getting out of the vehicle, be sure to press the [PWR] button on the main unit for 2
seconds or more while the power is still on, and then turn off the power.” If they forget to turn off
the power, the battery will be drained.
-
Vehicle connections
-
Tip
• You will need to purchase the necessary component adapter cable for the vehicle so that the power
supplies can be utilised. (Contact the dealer for further details.)
- -
5
System connection example
•
•
Never cut the insulation on the power cable or use it to power any other equipment. If the rated current
capacity of the power cable is exceeded, fire and electric shocks may result.
The cables should be secured with tape or a similar securing method to prevent any obstructions while
driving. If they get wound or entangled around components such as the steering wheel, shifting lever,
or brake pedal, accidents may result.
•
If removing the end of the cord to connect to another cord, be sure to wrap PVC tape or a similar wire
insulating method around the connection to insulate it. If the connection is not insulated, fire or
accidents may result.
Tip
Install and connect all of the peripheral units before connecting them to the main unit.
Do not remove any of the protective caps (RCA, etc.) unless in use.
•
•
MAIN UNIT
1
ANTENNA PLUG
16P
13P
DIN CABLE
(Supplied with CD changer)
TO EARTH
TO VEHICLE-SIDE
CONNECTOR
2
INTERCONNECTING
CABLE
(Power and speaker
connector)
DIGITAL OUT
(Do not remove cap)
13P
2P
CH3083
(sold separately)
TO EARTH
POWER CONNECTOR CABLE
(Supplied with CD changer)
- -
6
Installing the main unit
-
Installation angle
-
Front
Tip
To maintain proper function, the unit must be
mounted at less than 30 degrees. If the angle is in
excess of 30 degrees, CD skipping or ejection may
occur.
30˚ or less
Level (reference)
- Main unit installation example (If installing the main unit using the mounting sleeve) -
Tip
•
Carefully bind any excess length of cord that is
connected to the main unit and secure it to an
area of empty space in the vehicle so that it does
not move around or get caught in the main unit or
vehicle-side equipment. If the cords are not
handled correctly, operating problems or short-
circuits may occur, and this may result in the
danger of fire or other accidents.
Dashboard or console box
Bend the mounting
tabs.
•
Connect all cables before installing the main
unit.
3 Mounting sleeve
Insert the mounting sleeve into the opening in the
vehicle dashboard or console box.
1
2
Use a screwdriver or the like to bend the tabs in
the mounting sleeve to secure the mounting
sleeve.
Main unit
1
Attach the side brackets to the main unit using
flathead screws.
3
7
Flat head
screws
(Red:M5 x 8)
x 2
Tip
Be sure to use the supplied accessory mounting
screws (Red:M5 x 8) as the mounting screws. If
any other screws are used, they may damage the
inside of the unit.
Side brackets
4
Mount the stud bolt to the main unit.
4
5
Metal of vehicle
Insert the main unit into the mounting sleeve until
it locks in place.
Dashboard or console box
Fasten the rear of the main unit.
Install the bezel on the main unit.
6
7
9
Bushing
Tip
Stud bolt
8
•
•
Be careful not to forcefully push on the main unit's
display or buttons during installation. This may
result in damage to the main unit.
This installation method is only one example.
When installing the main unit to the vehicle, be
sure to as the place of purchase for information
on what installation method to use.
3
Mounting sleeve
5
Bezel
- -
7
- Main unit installation example (If installing the main unit using the side brackets of the vehicle) -
Tip
•
Carefully bind any excess length of cord that is
connected to the main unit and secure it to an
area of empty space in the vehicle so that it does
not move around or get caught in the main unit or
vehicle-side equipment. If the cords are not
handled correctly, operating problems or short-
circuits may occur, and this may result in the
danger of fire or other accidents.
Centre cluster panel
Pocket, etc
•
Connect all cables before installing the main
unit.
Remove the pocket and any other accessories
from the centre cluster to make room for the main
unit.
1
Mounting bolts
Remove the mounting brackets for the pocket.
2
3
Main unit
1
Attach the brackets to the main unit.
Tip
Be sure to use the supplied accessory mounting
screws (Red:M5 x 8) as the mounting screws. If
any other screws are used, they may damage the
inside of the unit.
Hex-head bolt
(Red:M5 x 8) x 4
6
Screw
x 4
Pocket
Install the main unit in the vehicle.
4
Mounting bracket
Hex-head bolt
Flat head
7
Tip
6
screw
(Red:M5 x 8) x 4
(Red:M5x8) x 4
•
Be careful not to forcefully push on the main unit's
display or buttons during installation. This may
result in damage to the main unit.
• This installation method is only one example.
When installing the main unit to the vehicle, be
sure to as the place of purchase for information
on what installation method to use.
Select the screws in accordance with the shapes
of the screw holes in the mounting bracket.
- -
8
|